System · Solid color epoxy
Solid color epoxy, the floor a warehouse actually needs
Pigmented epoxy squeegeed and back-rolled to a seamless, non-porous surface. It is the most cost-effective way to turn a raw slab into a floor you can wash, stripe and light properly — and for most industrial buildings it is the right answer rather than the cheap one.
Solid color epoxy at a glance
- Best for
- Warehouses, service bays, manufacturing, storage
- Build
- Prime + two pigmented coats + topcoat
- Finish
- Gloss, satin or matte
- Colors
- Mixed in-house to your spec
What it actually is
A 100% solids epoxy is two components that cure by chemical reaction rather than by evaporating a solvent. Nothing flashes off, so what you spread is what stays: a continuous film bonded into the profile of the concrete, with no seams, no grout lines and nothing porous for oil or dust to sit in.
A standard build is a penetrating primer, two pigmented coats and a topcoat, and the topcoat is where the floor is tuned. Urethane over epoxy buys abrasion resistance and holds gloss under UV; a matte or satin topcoat kills glare in a building with high-bay lighting. The colour is mixed to spec rather than chosen from six stock options.
Where it belongs
Warehouses, distribution floors, general manufacturing, storage, service bays, parts departments and back-of-house. Anywhere the requirement is a sound, sealed, bright floor that takes aisle striping and safety markings cleanly and can be washed rather than swept.
Light reflectance is an underrated part of the case. A pigmented floor in a dark building measurably lifts the light level without adding a single fixture, and in a high-bay warehouse that is a real operating saving as well as a safety one.
Where it does not belong
It is the wrong system for thermal shock and for aggressive wash-down. Epoxy is rigid, and a rigid film over a slab that is cycling between temperatures will eventually crack or disbond — that is urethane cement territory, not this.
It is also the wrong answer over a slab with a moisture problem you have not solved. Epoxy does not breathe. Vapor pressure under a non-permeable film will lift it in sheets, which is why moisture testing is not optional here, and why we test before we quote rather than after a failure.
And where tires are dragged daily — a busy service bay — a plain colour will hold tire marks that never fully come up. A flake or quartz broadcast hides that; flat colour advertises it.
Thickness, cure and return to service
A rolled or squeegeed build typically lands somewhere between 10 and 30 mils depending on the number of coats and whether the floor is being levelled as it goes. That is a film, not a mortar, and it depends entirely on the concrete beneath it for structure.
Foot traffic generally returns the day after the last coat; vehicle and rack traffic wants longer, and full chemical cure runs several days. Cold slabs slow everything down, which matters in an unheated Illinois or Wisconsin warehouse in February and is worth building into the schedule rather than discovering.
The prep it demands
Diamond grinding to a moderate ICRI 310.2R profile, with dust collection running so the work can happen inside a building that is still operating. Laitance, curing compound and any previous coating come off. Cracks are routed and filled and spalls are patched with new concrete rather than bridged with resin.
Moisture is measured to ASTM F2170 with in-situ relative humidity probes, or ASTM F1869 for a vapor emission rate. If the slab reads high, the honest answer is a different system or a moisture-mitigating primer, not a thicker coat of the same epoxy.
What we bring to it
We manufacture our own epoxy, so the colour is mixed in-house to your spec and the batch is proportioned for the conditions on site rather than shipped pre-blended for an average one. There is no distributor in the middle of that decision.
Most of the square footage behind our 350,000-plus is exactly this system, placed on nights and weekends in buildings that could not stop shipping to have a floor put down.
Solid color epoxy in place
Who specifies it
Where solid color epoxy gets called for
Warehouse & logistics
The default distribution floor: seamless, washable, and it takes aisle striping cleanly.
Aviation & hangars
Brightens a dark hangar and carries line work and equipment zones that have to read from above.
Dealerships & service shops
Parts departments, storage and back-of-house, where a wipe-clean floor is the whole requirement.
Day, night and weekend shifts. Estimates are free. Covering Midwest, East Coast and Southern states — out of Chicagoland, with finished floors in Gurnee, Kenosha, Milwaukee and Chicago.
The other five systems
Finished floors near you
Specifying solid color epoxy?
Tell us the square footage, the traffic and the downtime window. Estimates are free.